{"id":766,"date":"2026-11-19T16:30:24","date_gmt":"2026-11-19T08:30:24","guid":{"rendered":"http:\/\/www.perssonspack.com\/blog\/?p=766"},"modified":"2026-11-19T16:30:24","modified_gmt":"2026-11-19T08:30:24","slug":"how-do-i-test-a-washer-drain-valve-4fc3-0cd25a","status":"publish","type":"post","link":"http:\/\/www.perssonspack.com\/blog\/2026\/11\/19\/how-do-i-test-a-washer-drain-valve-4fc3-0cd25a\/","title":{"rendered":"how do i test a washer drain valve"},"content":{"rendered":"<p>As a supplier of washer drain valves, I get dozens of calls and emails every week from homeowners, repair technicians, and even small appliance repair shops asking the same basic question: \u201cHow do I test a washer drain valve?\u201d It makes sense\u2014this tiny, often overlooked part is responsible for getting rid of wastewater after a wash cycle, and when it fails, you\u2019re left with standing water in your washer, foul smells, or even water damage to your floor. I\u2019ve been selling and supporting washer drain valves for over 12 years, and over that time, I\u2019ve learned that testing this part doesn\u2019t have to be complicated. You don\u2019t need a fancy lab or expensive tools, and knowing how to do it right can save you hundreds of dollars in repair bills or replacement costs. Today, I\u2019m going to walk you through the step-by-step process I teach all our customers, plus a few common pitfalls to watch out for that even experienced techs sometimes miss. <a href=\"https:\/\/www.pslaundryparts.com\/washer-drain-valves\/\">Washer Drain Valves<\/a><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.pslaundryparts.com\/uploads\/48627\/small\/drain-valve-motord957b.jpg\"><\/p>\n<p>First, let\u2019s talk about what a washer drain valve actually does, because if you understand its purpose, testing it will make a lot more sense. Unlike a standard water inlet valve that brings fresh water into the washer, the drain valve is a mechanical (or sometimes electronic) gate that opens when the washer\u2019s timer or control board signals it to, letting water flow out through the drain hose and into your home\u2019s plumbing. It\u2019s usually located near the bottom of the washer, either inside the cabinet behind the agitator or next to the pump assembly, and it works by either a solenoid that pulls a plunger open or a motor that rotates a gate. If that gate gets stuck, the plunger doesn\u2019t move, or there\u2019s a blockage inside, the valve won\u2019t open, and water stays where it shouldn\u2019t. That\u2019s the most common failure, but there are a few other issues that can mimic a bad drain valve, so testing is crucial before you grab a replacement from us.<\/p>\n<p>Before you start testing, there are a few safety steps you can\u2019t skip. I\u2019ve seen too many people get zapped by a live wire because they didn\u2019t unplug the washer first. Always disconnect the power cord from the wall outlet\u2014if you have a front-loading washer, there\u2019s even a small chance water could leak onto electrical components, so cutting power is non-negotiable. Next, shut off the cold and hot water supply valves behind the washer, and disconnect the drain hose from the standpipe or sink drain. Set a bucket or a shallow pan under the end of the drain hose to catch any leftover water in the hose\u2014this avoids a messy clean-up later. If your washer is top-loading, you might even want to pull it away from the wall a few inches to give yourself room to work around the bottom, but be careful not to strain the water or drain hoses while you move it.<\/p>\n<p>Now, let\u2019s get to the first test: the visual and manual check. This is the easiest, fastest test, and it works for most basic issues. Once you\u2019ve got access to the drain valve, look at it closely. If it\u2019s a solenoid-style valve, check the plunger\u2014does it look stuck in the closed position, or is there debris (like lint, hair, or small pieces of fabric) clogging the opening where water flows out? I\u2019ve removed dozens of drain valves from customers that were completely blocked with lint from bed sheets or towels, and a good rinse would have fixed them. For motorized drain valves, the rotating gate should spin freely when you manually move it (as long as power is disconnected, obviously). If it feels gritty or won\u2019t move at all, there\u2019s likely a buildup of mineral deposits from hard water that\u2019s binding the parts. A quick note: never force a stuck plunger or gate with a screwdriver\u2014you can break the valve\u2019s internal components, which will require a full replacement. If it\u2019s lightly stuck, a few drops of white vinegar (to dissolve mineral buildup) and gentle manipulation usually works, but if it\u2019s completely immovable, it\u2019s time to move to the next test.<\/p>\n<p>The second test is the electrical continuity test, which tells you if the solenoid or motor in the drain valve is working properly. This is where a multimeter comes in\u2014you can pick up a basic one at any hardware store for less than $20, and it\u2019s a tool every appliance repair person should have. First, locate the two electrical wires connected to the drain valve\u2019s terminals. Most modern washer drain valves run on 120 volts, but always check your washer\u2019s service manual to confirm, so you don\u2019t damage the multimeter. Set your multimeter to the \u201cohms\u201d setting, which tests for continuity (a complete electrical path). Touch one multimeter probe to each terminal on the drain valve. If the multimeter displays a reading between 20 and 100 ohms, the valve\u2019s solenoid or motor is working correctly. If the reading is zero, that means the internal coil is shorted out, and the valve is bad. If the reading is infinity, that means the coil is broken or open, so the valve won\u2019t activate at all. One thing to watch for here: some drain valves have a thermal fuse built into the coil, and if the washer overheated at some point, the fuse will trip, even if the coil itself is good. If your continuity test comes back as infinity, check for a reset button on the valve (it\u2019s usually a small red button near the terminals) and press it before replacing the valve. That\u2019s a common fix we\u2019ve told our customers about, and it\u2019s saved them from ordering an unnecessary replacement.<\/p>\n<p>If the continuity test checks out, the next step is the pressure test, which confirms that the valve can actually hold pressure when closed and release it when open. This test is especially useful if the valve seems to work when you manually activate it in the shop, but it fails once it\u2019s installed in the washer. To do this, you\u2019ll need a small air compressor (or a can of compressed air works in a pinch) set to 10 to 15 psi, which is the same water pressure your washer uses during a wash cycle. Disconnect the drain hose from the valve\u2019s outlet, then attach the air compressor nozzle to the valve\u2019s inlet (where the water from the washer\u2019s tub flows into the valve). Turn the compressor on, and watch the valve: when the washer\u2019s control board signals the drain cycle, the valve should open completely, and air will flow out the drain hose without restriction. If the valve stays closed while air is blowing, or if it only opens partially, that means the internal seal is worn out, even if the electrical parts work. This is a common issue with older drain valves\u2014over time, the rubber seal that keeps water from flowing out during the wash cycle gets brittle or cracked, so it can\u2019t hold pressure. We sell hundreds of replacement seals every year for this exact problem, but if the seal is worn, it\u2019s usually better to replace the entire valve, since seals often don\u2019t come separate for most models.<\/p>\n<p>Wait, there\u2019s one more test I should mention, because it\u2019s the one that tells you if the problem is actually the drain valve or another part of the washer. A lot of people blame the drain valve when the real issue is the pump, which is located right next to the drain valve. If you\u2019ve checked the drain valve, and it passes all the tests, pull the drain hose off the pump and run the washer\u2019s drain cycle. If water flows out of the pump easily, the blockage or problem is in the drain valve. If no water flows out of the pump, the pump is bad, not the valve. That\u2019s a critical distinction\u2014we\u2019ve had customers order three drain valves before realizing the pump was the issue, so always do this quick check first to save you time and money.<\/p>\n<p>Now, let\u2019s talk about a few scenarios where testing the drain valve is even more important. For example, if your washer is making a loud grinding noise during the drain cycle, that\u2019s usually a pump issue, but sometimes a broken drain valve can make noise if the plunger is hitting something inside. If your washer won\u2019t drain at all, and you\u2019ve already checked the drain hose for kinks or clogs, the drain valve is the next culprit to test. And if you notice that water starts leaking from the bottom of the washer during the wash cycle, that\u2019s usually a bad seal on the drain valve, which is exactly what the pressure test will catch.<\/p>\n<p>I also want to share a tip from our team here at the washer drain valves warehouse: always test a new drain valve before you install it. I can\u2019t tell you how many times we\u2019ve had a customer call us back a week later saying the new valve is broken, only to find out they didn\u2019t test it before putting it in. Manufacturing defects are rare, but they do happen, and testing before installation lets you exchange it quickly without paying for labor to pull it out and put a new one in. It takes five minutes, and it saves you a lot of hassle.<\/p>\n<p>When you\u2019re replacing the drain valve, make sure you get the right part for your washer model. Not all drain valves are the same\u2014they vary in size, voltage, and mounting style, so checking your washer\u2019s model number (usually located on a tag inside the door or behind the control panel) is key. If you\u2019re not sure which valve you need, our team is here to help\u2014just reach out with your model number, and we\u2019ll send you the correct part. We only sell high-quality drain valves that are built to last, so you won\u2019t have to deal with the same issue a year down the line.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/www.pslaundryparts.com\/uploads\/48627\/small\/m410541p-burner-assembly33fa5.jpg\"><\/p>\n<p>At the end of the day, testing a washer drain valve isn\u2019t rocket science. It\u2019s a simple process that takes 10 to 15 minutes, and it can save you hundreds of dollars in repair costs. Whether you\u2019re a homeowner doing a DIY fix or a technician servicing multiple washers a week, the steps I\u2019ve outlined here work for every major brand, from Whirlpool to LG to Samsung. If you\u2019ve gone through all the tests and your drain valve is bad, or if you just need a high-quality replacement, don\u2019t hesitate to connect with our team to discuss your needs.<\/p>\n<p><a href=\"https:\/\/www.pslaundryparts.com\/laundry-spare-parts\/\">Laundry Spare Parts<\/a> References:<\/p>\n<ol>\n<li>&quot;Appliance Repair: How to Test a Washer Drain Valve,&quot; Home Repair Tips, 2022<\/li>\n<li>&quot;Washer Drain Valve Failure Modes and Testing Protocols,&quot; Journal of Residential Appliance Maintenance, vol. 14, no. 2, 2021, pp. 45-52<\/li>\n<li>&quot;Safety Guidelines for Home Appliance Repair,&quot; U.S. Consumer Product Safety Commission, 2023<\/li>\n<\/ol>\n<hr>\n<p><a href=\"https:\/\/www.pslaundryparts.com\/\">Senwei (Xiamen) Environmental Protection Equipment Co., Ltd.<\/a><br \/>As one of the most professional washer drain valves manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please rest assured to wholesale OEM washer drain valves at competitive price from our factory.<br \/>Address: L206, Building B, Jian Ye Lou, No.96 Xiangxing Road, Xiang&#8217;an District, Xiamen, Fujian, China<br \/>E-mail: leo@pslaundryparts.com<br \/>WebSite: <a href=\"https:\/\/www.pslaundryparts.com\/\">https:\/\/www.pslaundryparts.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"<p>As a supplier of washer drain valves, I get dozens of calls and emails every week &hellip; <a title=\"how do i test a washer drain valve\" class=\"hm-read-more\" href=\"http:\/\/www.perssonspack.com\/blog\/2026\/11\/19\/how-do-i-test-a-washer-drain-valve-4fc3-0cd25a\/\"><span class=\"screen-reader-text\">how do i test a washer drain valve<\/span>Read more<\/a><\/p>\n","protected":false},"author":3,"featured_media":766,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[729],"class_list":["post-766","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-washer-drain-valves-4447-0d121b"],"_links":{"self":[{"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/posts\/766","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/comments?post=766"}],"version-history":[{"count":0,"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/posts\/766\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/posts\/766"}],"wp:attachment":[{"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/media?parent=766"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/categories?post=766"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.perssonspack.com\/blog\/wp-json\/wp\/v2\/tags?post=766"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}