Posted in

how do i test a washer drain valve

As a supplier of washer drain valves, I get dozens of calls and emails every week from homeowners, repair technicians, and even small appliance repair shops asking the same basic question: “How do I test a washer drain valve?” It makes sense—this tiny, often overlooked part is responsible for getting rid of wastewater after a wash cycle, and when it fails, you’re left with standing water in your washer, foul smells, or even water damage to your floor. I’ve been selling and supporting washer drain valves for over 12 years, and over that time, I’ve learned that testing this part doesn’t have to be complicated. You don’t need a fancy lab or expensive tools, and knowing how to do it right can save you hundreds of dollars in repair bills or replacement costs. Today, I’m going to walk you through the step-by-step process I teach all our customers, plus a few common pitfalls to watch out for that even experienced techs sometimes miss. Washer Drain Valves

First, let’s talk about what a washer drain valve actually does, because if you understand its purpose, testing it will make a lot more sense. Unlike a standard water inlet valve that brings fresh water into the washer, the drain valve is a mechanical (or sometimes electronic) gate that opens when the washer’s timer or control board signals it to, letting water flow out through the drain hose and into your home’s plumbing. It’s usually located near the bottom of the washer, either inside the cabinet behind the agitator or next to the pump assembly, and it works by either a solenoid that pulls a plunger open or a motor that rotates a gate. If that gate gets stuck, the plunger doesn’t move, or there’s a blockage inside, the valve won’t open, and water stays where it shouldn’t. That’s the most common failure, but there are a few other issues that can mimic a bad drain valve, so testing is crucial before you grab a replacement from us.

Before you start testing, there are a few safety steps you can’t skip. I’ve seen too many people get zapped by a live wire because they didn’t unplug the washer first. Always disconnect the power cord from the wall outlet—if you have a front-loading washer, there’s even a small chance water could leak onto electrical components, so cutting power is non-negotiable. Next, shut off the cold and hot water supply valves behind the washer, and disconnect the drain hose from the standpipe or sink drain. Set a bucket or a shallow pan under the end of the drain hose to catch any leftover water in the hose—this avoids a messy clean-up later. If your washer is top-loading, you might even want to pull it away from the wall a few inches to give yourself room to work around the bottom, but be careful not to strain the water or drain hoses while you move it.

Now, let’s get to the first test: the visual and manual check. This is the easiest, fastest test, and it works for most basic issues. Once you’ve got access to the drain valve, look at it closely. If it’s a solenoid-style valve, check the plunger—does it look stuck in the closed position, or is there debris (like lint, hair, or small pieces of fabric) clogging the opening where water flows out? I’ve removed dozens of drain valves from customers that were completely blocked with lint from bed sheets or towels, and a good rinse would have fixed them. For motorized drain valves, the rotating gate should spin freely when you manually move it (as long as power is disconnected, obviously). If it feels gritty or won’t move at all, there’s likely a buildup of mineral deposits from hard water that’s binding the parts. A quick note: never force a stuck plunger or gate with a screwdriver—you can break the valve’s internal components, which will require a full replacement. If it’s lightly stuck, a few drops of white vinegar (to dissolve mineral buildup) and gentle manipulation usually works, but if it’s completely immovable, it’s time to move to the next test.

The second test is the electrical continuity test, which tells you if the solenoid or motor in the drain valve is working properly. This is where a multimeter comes in—you can pick up a basic one at any hardware store for less than $20, and it’s a tool every appliance repair person should have. First, locate the two electrical wires connected to the drain valve’s terminals. Most modern washer drain valves run on 120 volts, but always check your washer’s service manual to confirm, so you don’t damage the multimeter. Set your multimeter to the “ohms” setting, which tests for continuity (a complete electrical path). Touch one multimeter probe to each terminal on the drain valve. If the multimeter displays a reading between 20 and 100 ohms, the valve’s solenoid or motor is working correctly. If the reading is zero, that means the internal coil is shorted out, and the valve is bad. If the reading is infinity, that means the coil is broken or open, so the valve won’t activate at all. One thing to watch for here: some drain valves have a thermal fuse built into the coil, and if the washer overheated at some point, the fuse will trip, even if the coil itself is good. If your continuity test comes back as infinity, check for a reset button on the valve (it’s usually a small red button near the terminals) and press it before replacing the valve. That’s a common fix we’ve told our customers about, and it’s saved them from ordering an unnecessary replacement.

If the continuity test checks out, the next step is the pressure test, which confirms that the valve can actually hold pressure when closed and release it when open. This test is especially useful if the valve seems to work when you manually activate it in the shop, but it fails once it’s installed in the washer. To do this, you’ll need a small air compressor (or a can of compressed air works in a pinch) set to 10 to 15 psi, which is the same water pressure your washer uses during a wash cycle. Disconnect the drain hose from the valve’s outlet, then attach the air compressor nozzle to the valve’s inlet (where the water from the washer’s tub flows into the valve). Turn the compressor on, and watch the valve: when the washer’s control board signals the drain cycle, the valve should open completely, and air will flow out the drain hose without restriction. If the valve stays closed while air is blowing, or if it only opens partially, that means the internal seal is worn out, even if the electrical parts work. This is a common issue with older drain valves—over time, the rubber seal that keeps water from flowing out during the wash cycle gets brittle or cracked, so it can’t hold pressure. We sell hundreds of replacement seals every year for this exact problem, but if the seal is worn, it’s usually better to replace the entire valve, since seals often don’t come separate for most models.

Wait, there’s one more test I should mention, because it’s the one that tells you if the problem is actually the drain valve or another part of the washer. A lot of people blame the drain valve when the real issue is the pump, which is located right next to the drain valve. If you’ve checked the drain valve, and it passes all the tests, pull the drain hose off the pump and run the washer’s drain cycle. If water flows out of the pump easily, the blockage or problem is in the drain valve. If no water flows out of the pump, the pump is bad, not the valve. That’s a critical distinction—we’ve had customers order three drain valves before realizing the pump was the issue, so always do this quick check first to save you time and money.

Now, let’s talk about a few scenarios where testing the drain valve is even more important. For example, if your washer is making a loud grinding noise during the drain cycle, that’s usually a pump issue, but sometimes a broken drain valve can make noise if the plunger is hitting something inside. If your washer won’t drain at all, and you’ve already checked the drain hose for kinks or clogs, the drain valve is the next culprit to test. And if you notice that water starts leaking from the bottom of the washer during the wash cycle, that’s usually a bad seal on the drain valve, which is exactly what the pressure test will catch.

I also want to share a tip from our team here at the washer drain valves warehouse: always test a new drain valve before you install it. I can’t tell you how many times we’ve had a customer call us back a week later saying the new valve is broken, only to find out they didn’t test it before putting it in. Manufacturing defects are rare, but they do happen, and testing before installation lets you exchange it quickly without paying for labor to pull it out and put a new one in. It takes five minutes, and it saves you a lot of hassle.

When you’re replacing the drain valve, make sure you get the right part for your washer model. Not all drain valves are the same—they vary in size, voltage, and mounting style, so checking your washer’s model number (usually located on a tag inside the door or behind the control panel) is key. If you’re not sure which valve you need, our team is here to help—just reach out with your model number, and we’ll send you the correct part. We only sell high-quality drain valves that are built to last, so you won’t have to deal with the same issue a year down the line.

At the end of the day, testing a washer drain valve isn’t rocket science. It’s a simple process that takes 10 to 15 minutes, and it can save you hundreds of dollars in repair costs. Whether you’re a homeowner doing a DIY fix or a technician servicing multiple washers a week, the steps I’ve outlined here work for every major brand, from Whirlpool to LG to Samsung. If you’ve gone through all the tests and your drain valve is bad, or if you just need a high-quality replacement, don’t hesitate to connect with our team to discuss your needs.

Laundry Spare Parts References:

  1. "Appliance Repair: How to Test a Washer Drain Valve," Home Repair Tips, 2022
  2. "Washer Drain Valve Failure Modes and Testing Protocols," Journal of Residential Appliance Maintenance, vol. 14, no. 2, 2021, pp. 45-52
  3. "Safety Guidelines for Home Appliance Repair," U.S. Consumer Product Safety Commission, 2023

Senwei (Xiamen) Environmental Protection Equipment Co., Ltd.
As one of the most professional washer drain valves manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please rest assured to wholesale OEM washer drain valves at competitive price from our factory.
Address: L206, Building B, Jian Ye Lou, No.96 Xiangxing Road, Xiang’an District, Xiamen, Fujian, China
E-mail: leo@pslaundryparts.com
WebSite: https://www.pslaundryparts.com/